APEXi AFC neo for sale SOLD!

[brccrx]

As the title say ive APEXi neo air and fuel controller for sale, it was on my white GRvR and it was mapped but all maps are cleared to give You a fresh start. Dont need it anymore as ive finally found plastic case ECU for Mivec.

Can be used to tune the AFR and to control Mivec engaging point, comes with wiring harness.
There more features that im not familiar with so just have a read here:

http://www.apexi-usa.com/store/electron ... ement.html

Pics





Price:

140 Delivered registered post
135 Delivered via Parcel Motel
130 Collected

Thanks for looking.

[d_dan]

Had one of these before made a nice difference for torque. (can also be used to get your car through the NCT/ more MPG if thats your thing)

[brccrx]

Was that N/A dan? Much of a differeence to the torque?

Lol, i never thought of the NCT and fuel consumption reasons
Thanks!

[d_dan]

yes NA GPX with
- ARC intake chamber
- 5zigen pro racer Aspec
- Decat
- HKS mushroom filter

It made a little over 7LBS and 1.4 HP but it made the power at lower ranges from the map.

[brccrx]

I know im asking for a lot but would You be able to post the dyno before and after print out pics or just pm it to me please?

[mivecrx]

yes NA GPX with
- ARC intake chamber
- 5zigen pro racer Aspec
- Decat
- HKS mushroom filter

It made a little over 7LBS and 1.4 HP but it made the power at lower ranges from the map.

What power did the car make?

[d_dan]

199.8 hp with 157.6lbs a
S far as I remember.

[mivecrx]

199.8 hp with 157.6lbs a
S far as I remember.

That's serious, neo couldn't pull much out of that.

[d_dan]

That's with the neo.

[mivecrx]

That's with the neo.

I know, I mean it couldn't get anymore because obviously the car was in very good health and running almost perfect

[brccrx]

Where did ya dyno it dan? U wouldnt have the print outs by any chance?

Edit:

Just found Your post in this topic:

viewtopic.php?f=1&t=6845

where ya state its thats without neo as the spec doesnt say U had it on board when You got the Car?

Just put up a post there witth the full readout but 207.3 BHP
With 148.6 LBS

Could You clarify please?

[d_dan]

Thats not the correct post that was the day I bought the fto. Dyno'd at westward

[brccrx]

U cant be serious or U have the dyno print out?

Westward dyno is most conservative dyno out them all to be honest!

[mivecrx]

U cant be serious or U have the dyno print out?

Westward dyno is most conservative dyno out them all to be honest!

Westward tells the truth!

[Bernard]

It's where we went for the club dyno day, their reputation is absolutely 100% deserved.

[mivecrx]

It's where we went for the club dyno day, their reputation is absolutely 100% deserved.

They use a Maha chassis dyno which are rated highly. If Martin has time he usually tells you how the cars running and what tuning can be done.

If I remember correctly it's €180 for Martin to map a neo, including dyno prints before and after.

[brccrx]

I agree with ye lads, but who ever U ask and he is in to modding cars he will tell ya that Martins dyno show lower figures than even factory ones?

Bernard is there any topic on the site from the club dyno day where we could have a look at the results?

[Bernard]

In the meets section...
http://www.fto-ireland.com/forum/viewtopic.php?f=3&t=14233

[brccrx]

Thank You!

[brccrx]

Gone!